|
8-Jan-2017, 8:44 PM
|
#1
|
Junior Member
Join Date: Jan 2017
Location: Outside of Memphis
Posts: 6
|
West of Memphis
Hello,
I live about 10 miles WNW of Memphis ( http://www.tvfool.com/?option=com_wr...dfaf24593877d4 ). I currently have Directv with 3 televisions. I also have Directv Now. I want to get rid of the satellite service but still need to get the local networks on all three televisions.
I hope to get the following channels listed in order of importance:
NBC - WMC - 5.1 (VHF-Lo)
CBS - WREG - 3.1 (UHF)
Fox - WHBQ - 13.1 (VHF-High)
ABC - WATN - 24.1 (UHF)
PBS - WKNO - 10.1 (UHF)
CW - WLMT - 30.1 (UHF)
I can mount an antenna in a 2nd story unfinished bonus room above my garage. It faces ENE at about 85° and has a window. It would be about 18' above ground with no tall structures or trees in sight.
I understand that anything below the roof is less than optimal, but its a risk I'm willing to take. If all else fails, I'll just keep the satellite service.
3 televisions with 30' - 50' runs.
I will also consider any indoor models as long as they would work in all three rooms. I can remember as a child (early '80s) having a television with the built-in rabbit ears being able to pick up channel 5 from further away than I am now but have no idea where their tower was then.
Thanks.
WMCTV recommends the following two antennas:
Indoors: GE 24734 Millennium HDTV TV Antenna - I ordered this as a long-shot. It should be here Monday evening.
Outdoors: Channel Master CM-3016
*I also posted on another forum while awaiting access to this one.
Last edited by Horripillation; 8-Jan-2017 at 8:50 PM.
|
|
|
8-Jan-2017, 10:47 PM
|
#2
|
Senior Member
Join Date: Dec 2013
Location: Eastern Ohio
Posts: 101
|
The GE looks like a unamplified set of rabbit ears so I would expect that to work for one TV if the antenna is near a window and you get it adjusted right.
Due to reflections and near field interactions, a directional antenna would likely be more stable though
Since you need low and high vhf as well as UHF, a small combo antenna like the winegard HD7010 should do a fine job and pull in enough signal to feed all three TVs.
Warren electronics.com has them listed at $45.71
|
|
|
11-Jan-2017, 10:40 AM
|
#3
|
Junior Member
Join Date: Jan 2017
Location: Outside of Memphis
Posts: 6
|
The GE 24734 Millennium HDTV TV Antenna finally arrived yesterday. Hooked it up and scanned channels multiple times with the antenna in multiple configurations.
Could get all channels I wanted plus some reliably except for 5.1 and 13.1. Sometimes 13.1 would come in fine, but activity around the tv could easily disrupt it. Could not get 5.1 at all.
So, time to gather money and get motivated to order an outdoor antenna for the attic.
|
|
|
11-Jan-2017, 11:23 AM
|
#4
|
Antennas Direct Tech Supp
Join Date: Jan 2010
Posts: 2,942
|
Either the CM3016 you proposed or the Winegard 7010 that WE suggested are suitbable choices. Those two are comparable models.
I'm not surprised that the GE didn't pick up your local channel 5 as it needs those long elements that the other two antennas have.
|
|
|
12-Jan-2017, 4:25 AM
|
#5
|
Junior Member
Join Date: Jan 2017
Location: Outside of Memphis
Posts: 6
|
Quote:
Originally Posted by ADTech
Either the CM3016 you proposed or the Winegard 7010 that WE suggested are suitbable choices. Those two are comparable models.
I'm not surprised that the GE didn't pick up your local channel 5 as it needs those long elements that the other two antennas have.
|
I didn't expect the GE to work on 5. I just had to try before spending the money. It would have been awful to set up the full system then find a neighbor happily watching with their GE I didn't even try. Plus the rabbit ears were much shorter than I imagined.
In a couple of weeks, I will probably get the CM3016 and a long coax. I bought a Holland Electronics 3-way splitter. I plan on running coax from antenna to my Directv box outside, into the splitter, then connect the 3 coax from the tv into it.
Some say I'll need a pre-amp, others say a power distribution amplifier, some say both, others say neither. So, I will start with just the splitter. I do not have any power outlets near the place I'm putting the antenna or the splitter box. So, if I need a powered option, I may have to bring in an electrician. Or use a light socket power outlet adaptor.
Anyway, it will probably be a couple of weeks. My next 2 weekends are booked.
Thanks.
|
|
|
12-Jan-2017, 11:26 AM
|
#6
|
Antennas Direct Tech Supp
Join Date: Jan 2010
Posts: 2,942
|
Quote:
So, I will start with just the splitter.
|
A prudent choice. Be sure you remove any DirectTV-supplied devices such as their power inserter and their SWiM splitters or any other multi-switch from the line(s)
Quote:
I do nor have any power outlets near the place I'm putting the antenna or the splitter box
|
Don't need one there. Good distribution amps and all pre-amps allow for power to be supplied remotely via one of the output signal lines. Here's an app note I wrote a while back that still applies. https://www.antennasdirect.com/cmss_...lations-V2.pdf I've also added a copy as an attachment, just click on the link below to download.
Power inserters are now available at Amazon among other places, just search for "amplifier power inserter" and several will pop up.
Last edited by ADTech; 12-Jan-2017 at 11:31 AM.
|
|
|
13-Jan-2017, 6:49 AM
|
#7
|
Junior Member
Join Date: Jan 2017
Location: Outside of Memphis
Posts: 6
|
Quote:
Originally Posted by ADTech
A prudent choice. Be sure you remove any DirectTV-supplied devices such as their power inserter and their SWiM splitters or any other multi-switch from the line(s)
Don't need one there. Good distribution amps and all pre-amps allow for power to be supplied remotely via one of the output signal lines. Here's an app note I wrote a while back that still applies. https://www.antennasdirect.com/cmss_...lations-V2.pdf I've also added a copy as an attachment, just click on the link below to download.
Power inserters are now available at Amazon among other places, just search for "amplifier power inserter" and several will pop up.
|
Great news about the power inserter. Thanks!
I've ordered the CM-3016 / coax / tripod stand.
Hopefully will find the time to install soon.
1/23/17 - Still haven't had time to install. Have antennae set-up. Just waiting for time on a dry day to finish work outside with wiring.
Last edited by Horripillation; 23-Jan-2017 at 10:09 PM.
|
|
|
27-Jan-2017, 2:31 PM
|
#8
|
Junior Member
Join Date: Jan 2017
Location: Outside of Memphis
Posts: 6
|
Quote:
Originally Posted by Horripillation
Great news about the power inserter. Thanks!
I've ordered the CM-3016 / coax / tripod stand.
Hopefully will find the time to install soon.
1/23/17 - Still haven't had time to install. Have antennae set-up. Just waiting for time on a dry day to finish work outside with wiring.
|
On Wednesday I hooked everything up. Received all the channels I wanted clearly except for some occasional pixelation on Channel 13. I then went to the splitter and unhooked the coax to TV's 2 and 3. Went back to TV 1 and everything cleared up.
This leads me to believe I need the distribution amplifier. Per @ADTech's suggestion, I've ordered a power inserter. I'd like some suggestions on a 4 port distribution amplifier.
Thanks!!!
|
|
|
27-Jan-2017, 2:50 PM
|
#9
|
Antennas Direct Tech Supp
Join Date: Jan 2010
Posts: 2,942
|
You should not need additional amplification (it will likely cause NEW problems), you need to identify and resolve the fault that is specific to reception channel 13. Your channel 13 is calculated to be line of sight with a signal margin that should, once antenna gain is added, exceeds 50 dB. In plain linear numbers, that's 100,000 times more signal power than the tuner needs. If you amplify at all, you will boost all of the other signals, some into the range where they will likely overload either the amp or the tuner(s).
Common reasons for a single channel to be of poor reception strength or quality:
Antenna placement - partially blocked signal path, often exhibits as being specific to a single channel whether UHF or VHF.
Localized interference from electrical or electronic devices and wiring.
For VHF channels 4-13, strong FM signals. Requires some math and additional detective work to develop that theory.
Fault in a cable or in-line device that causes it to "suck out" a particular frequency or set thereof. Worn-out female F-connectors or coax center conductors that are a bit too short are a common faults.
You can try a four-port amp like the one we carry and give it a shot. It won't overload internally, but it's not possible to be assured that the same won't happen downstream.
Last edited by ADTech; 27-Jan-2017 at 2:52 PM.
|
|
|
27-Jan-2017, 3:25 PM
|
#10
|
Retired A/V Tech
Join Date: Aug 2012
Location: S.E. VA
Posts: 2,750
|
As ADTech mentioned, your signals are very strong, and you shouldn't need a distribution amp, but your test seems to indicate that you do.
If your antenna is mounted inside, the signals could be weaker than listed on the report.
The signals from my indoor antenna are about 20 dB weaker than my report.
Where is your antenna located?
Is it aimed at 94 degrees magnetic?
If it is inside, is it aimed at a wall or out a window?
An FM signal report based on an estimate of your location:
http://www.fmfool.com/modeling/tmp/4...1/Radar-FM.png
If electrical interference was causing a problem for 13, it would probably also affect 5. You can listen for electrical interference on an AM portable radio tuned to an unused frequency at the low 540 end or the high 1600 end of the dial.
Last edited by rabbit73; 27-Jan-2017 at 7:20 PM.
|
|
|
27-Jan-2017, 6:18 PM
|
#11
|
Antennas Direct Tech Supp
Join Date: Jan 2010
Posts: 2,942
|
Quote:
If electrical interference was causing a problem for 13, it would probably also affect 5.
|
Maybe, but maybe not. Lot's of possibilities.
The AM radio tip is a good one to try, it may yield clues to the issue.
|
|
|
26-Mar-2017, 2:08 PM
|
#12
|
Junior Member
Join Date: Jan 2017
Location: Outside of Memphis
Posts: 6
|
Last weekend, I finally unhooked all DTV equipment and connected antenna to all three tvs. Works perfectly!
All local channels come in clear.
All I used was the antenna and 3 way splitter.
You guys have been wonderful. Thank You!!!!!
|
|
|
26-Mar-2017, 3:12 PM
|
#13
|
Retired A/V Tech
Join Date: Aug 2012
Location: S.E. VA
Posts: 2,750
|
Thanks for the update; glad that it is working well for you.
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
|