TV Fool  

Go Back   TV Fool > Special Forums > General Site Feedback / Discussion

Notices

Reply
 
Thread Tools
Old 25-Mar-2016, 6:17 PM   #1
ragoo43
Junior Member
 
Join Date: Dec 2015
Posts: 1
Grounding an antenna mast

I have an outdoor antenna that I am going to install. I need to ground it. I have 50 ft of #6 bare ground conductor. What else do I need to attach to house? Standoffs? something else? Can go up against vinyl siding? Thanks in advance
ragoo43 is offline   Reply With Quote
Old 26-Mar-2016, 5:16 AM   #2
SWHouston
An Old Member
 
SWHouston's Avatar
 
Join Date: Jan 2010
Location: Houston, Tx. USA
Posts: 15
How are you going to mount your antenna...
(mast/eve/"J" Mount/ ?

No need to use the heavy wire...
Unless you are using a Mast, and required by City Code.
Get a inline grounding coupling, and use the Shield as a ground.*
A Mast may not be so tall, where should it fall, any part of it must not touch the next property.

No, don't directly attach any bare wire to your house.
If you get a direct strike, it could cause enough heat to start a fire.

There are three kinds of Lightning Strike...
Distant:
Will cause an electrical surge, which you may already be protected against through electronics in your equipment. If unknown, you may use a Power Strip which has Surge Protection built into it.
Near:
Where EMP is transmitted through the atmosphere to your Antenna. Usually messes up tuners, and there's nothing you can do to protect your equipment from it, other than what the Manufacturer has installed.
Direct:
Kiss your entire system goodbye, and, hope the molten metal doesn't start a fire.

*= Placement of the Grounding Coupling is a topic of protracted discussion.
__________________
Good Golf, good OTA/HDTV and anything else that makes you HAPPY
OTA: AntennaCraft/RS VU-90XR (Attic Mt). DTVPal DVR, Sony RDR-VXD655, WinTV HVR-850-1200.
D/A: Samsung H260F, Winegard RC-DT09A, DTVPal Plus.
Typical OTA Reception Houston TX 77033

Last edited by SWHouston; 6-Apr-2016 at 4:54 AM.
SWHouston is offline   Reply With Quote
Old 27-Mar-2016, 11:34 AM   #3
rabbit73
Retired A/V Tech
 
Join Date: Aug 2012
Location: S.E. VA
Posts: 1,863
If the antenna is outside, the coax shield should be grounded with a grounding block that is connected to the house electrical system ground with 10 gauge copper wire for electrical safety and to reject interference. For further compliance with the electrical code (NEC), the mast should also be grounded in a similar manner to drain any buildup of static charge, but the system will not survive a direct strike.





Grounding 101
http://www.highdefforum.com/local-hd...ing-101-a.html

Satellite System Grounding
Part 2 - NEC Overview
Presented by Todd Humphrey

http://www.dbsinstall.com/diy/Grounding-2.asp

Todd Humphrey doesn't speak for the NFPA that publishes the NEC code, but he has some ideas that are helpful. The local electrical inspector (AHJ, authority having jurisdiction) has the final say if you are willing to get him involved. Some inspectors are more friendly than others; a local electrician could tell you.
__________________
If you can not measure it, you can not improve it.
Lord Kelvin, 1883
http://www.megalithia.com/elect/aeri...ttpoorman.html

Last edited by rabbit73; 27-Mar-2016 at 2:33 PM.
rabbit73 is online now   Reply With Quote
Reply

Bookmarks

Go Back   TV Fool > Special Forums > General Site Feedback / Discussion


Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off




All times are GMT. The time now is 2:43 AM.


Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Copyright © TV Fool, LLC