PDA

View Full Version : Mxv5100 series vhf/fm antenna


Nascarken
12-Jul-2016, 4:02 AM
Does anyone no what dBm: is , and the receive, distance and is it HI & LOW VHF,? Boom length,15FT, WELL EVERYONE HAVE A GOOD DAY, AND THANKS EVERYONE FOR THE HELP,

rabbit73
13-Jul-2016, 12:55 AM
That IS a big antenna. I couldn't find any gain figures for it, but I did find a thread and some photos.

http://forums.wtfda.org/showthread.php?10554-Antennacraft-VHF-Antennas-Available

Nascarken
13-Jul-2016, 1:14 AM
We'll HI there rabbit 73 I have a story to tell about the antenna and it's an antennacraft old school vhf /FM TELEVISION ANTENNACRAFT M X V 5100

Nascarken
13-Jul-2016, 1:46 AM
We'll I PUT a post on from

Nascarken
13-Jul-2016, 11:49 AM
[QUOTE=Nascarken;55556]We'll I PUT a post

rabbit73
13-Jul-2016, 11:00 PM
What happened to your post with the story?

rabbit73
13-Jul-2016, 11:51 PM
I THOUGHT THAT WHEN YOU. USE A MAST MOUNT, AMPLIFIER THEY SAY, YOU SHOULD USE 18Gage solid copper RG 6 CLABLE,AND when using VHF yes or no,on this subject, not to copper, C ,steal CABLE? 73 And have a good day,The signal loss for coax with a copper clad steel center conductor is about the same as the signal loss for coax with a sold copper center conductor. This is because the signal only travels on the outside of the center conductor, which is called the "skin effect."

For both types of coax, the loss for VHF is much less than for UHF, which is about 6 dB per 100 feet for UHF.

However, the type of center conductor is important when you use a preamp, because the DC current for the preamp uses the whole cross section of the center conductor. The resistance of the copper clad steel conductor is greater than the resistance of the solid copper conductor, so the voltage drop for the preamp will be greater with the copper clad steel center conductor.

The general rule is up to 100 feet is OK for copper clad steel, and solid copper is OK up to 200 feet.

That rule is for preamps that use a voltage of about 15 to 20 volts.

If you have one of the new preamps that use USB 5V like the Winegard Boost LNA 200, the voltage drop becomes more critical.

I haven't seen any test results that show how low the voltage can go before the preamp performance is affected.

That would be a good experiment for someone to do.

Nascarken
15-Jul-2016, 1:32 AM
Can you do the test on this one Rabbit 73,

rabbit73
15-Jul-2016, 3:11 PM
I would like to test the LNA-200, but I don't have one, and I don't have my test equipment with me at my present location.

Nascarken
15-Jul-2016, 3:27 PM
We'll sorry to hear that MXV 5100,SERIES can't ,find out what the DB gain Is OR specifications on it's f o u n t to back db is,???can you may be try to find something ,for me well thanks again and have a good day rabbit 73

rabbit73
15-Jul-2016, 6:12 PM
I looked, but could not find, specs for the MXV-5100; sorry.

It probably has more gain than the Antennacraft Y10-7-13 VHF Yagi on VHF-High:
http://www.antennacraft.com/pdfs/Y10-7-13.pdf

and more gain than the Winegard HD8200U on VHF-Low:
http://www.solidsignal.com/pview.asp?p=hd8200u

and more than the Winegard YA-1026:
http://www.starkelectronic.com/wya1026.htm

http://www.wtfda.org/nn2e/